450E Round Baler

  • Makes tight and dense 4’ x 5’ bales
  • Exclusive DiamondTough™ triple weave belts
  • Regular pickup on 450E Baler with converging wheels Regular pickup on 450E Baler with converging wheels

    Mounted in front of the baler wheels and directly below the bale chamber, the pickup hugs the ground for clean crop retrieval. Hay movement is minimized.

    • V-belt driven
    • 450E and 450M Baler pickups are 116.6 cm (45.9 in.) wide
    • Large reel shaft and reel bearing

    The small-diameter, low-profile pickup allows for good ground gauging and clean crop retrieval.

    • Handles large, heavy windrows of hay and high-moisture crops
    • Feeds hay directly to the forming chamber to reduce crop loss
    • Low-profile pickup minimizes hay lift to reduce chaffing and retain hay quality

    Side flares prevent hay from blowing off the pickup ends, which reduces hay loss.

    The closely-spaced pickup teeth extend to the baler side sheets to help build straight-edged bales.

    Standard on regular pickups, compressor rods are contoured to control hay over the pickup radius for positive feeding. The compressor rack can be adjusted upward or downward to match the volume of material in the windrow and can be easily removed to match crop conditions.

    Adjustable crank handle Adjustable crank handle

    The adjusting crank positions the pickup to the desired operating height to match crop or field conditions.

    An optional hydraulic pickup lift cylinder is available as an attachment.

    • Makes raising for transport or clearing obstructions easy
    • Crank handle serves as a down stop
    • Adapts to regular and MegaWide™ Plus pickups
    • Hydraulic pickup lift comes standard on premium machines

    NOTE: Crank is not an option for the MegaWide High Capacity and Cutting (HC2) feed system.

  • Audible alarm
    BaleTrak Pro monitor-controller BaleTrak Pro monitor-controller

    The BaleTrak Pro monitor-controller is included with the automatic electric twine tie option and the Edge-to-Edge net wrap option on the 450E Baler. The monitor sounds an alarm for near-full, full, and oversized bales.

    • Monitor beeps once to notify the operator to even-up the bale prior to reaching the desired size.
    • Monitor beeps twice when the bale reaches the desired size.
      • If the operator continues to feed hay into the baler, the monitor will sound continuously to warn of an oversized bale.
    • Bale shape bars are not available on the 450E Round Balers. The 450E Round Balers allow for adjustment of twine settings from the cab by using the BaleTrak Pro Monitor.
    • The number of wraps on the Edge-to-Edge net wrap option on the 450E can be set with the BaleTrak Pro.

    The audible level of the monitor can be adjusted.

  • Side view of adjustable hitch Side view of adjustable hitch
    Front view of adjustable hitch Front view of adjustable hitch

    The 0 Series Round Balers came standard with an adjustable hitch and this feature will continue to be in base with the 0 Series Round Balers. This feature allows the hitch height to be adjusted to optimize crop-feeding performance. Due to the wide array of tractor tire sizes and drawbar heights, hitch adjustment may be necessary to get the proper feed opening of the baler. The adjustable hitch eliminates the need for the 51-mm (2-in.) thick tractor drawbar kit (AE57344) because it has a wider opening.

    Benefits of the adjustable hitch:

    • Ability to match baler to numerous tire sizes
    • Allows for drawbar height to fall within 330 mm to 559 mm (13 in. to 22 in.) from the top of the drawbar to the ground
    • Eliminates narrow feed opening on the baler which can cause plugging
    • Allows pickup head to follow terrain without missing crop

    All eight bolts must be used when adjusting the hitch. There are four different positions as shown below:

    Position 1 (top) (factory setting) - regular pickups Position 1 (top) (factory setting) - regular pickups
    Position 2 Position 2
    Position 3 (factory setting) - MegaWide Plus and MegaWide HC<sup>2</sup> Position 3 (factory setting) - MegaWide Plus and MegaWide HC2
    Position 4 (bottom) Position 4 (bottom)
  • Bale-starting diagram Bale-starting diagram

    As the hay enters the forming chamber from the pickup, belts immediately turn the hay to form a tight, dense core.

    Incoming hay then feeds between the bale and the lower gate roll. Hay is tightly compressed into smooth, dense layers as it enters the bale.

    Chaffing is greatly reduced to prevent loss and retain hay quality in the bale.

    Full-sized bale in bale chamber Full-sized bale in bale chamber

    The idler arm rises with bale growth, forcing oil from the hydraulic cylinder through a pressure-relief valve to maintain uniform bale density throughout the bale-forming process.

  • Staggered belts Staggered belts

    John Deere's 178-mm (7-in.) wide diamond-tread design ensures fast bale starts and grips the bale to prevent slippage and reduce chaffing. The treads are self-cleaning to reduce carryover. The belts are staggered to reduce the loss of fine material and are closely spaced to contain the hay for fast, easy starts.

    The belts enclose 91 percent of the bale width to reduce loss of fine material and retain hay quality.

    The staggered belt roll design enables any loose hay under or behind the belts to be returned to the pickup and into the baler. This design helps to prevent buildup at the front of the baler, which could cause hay loss and belt or splice damage.

    DiamondTough triple-weave belts DiamondTough triple-weave belts
    #

    Every baler in the 0 Series Family uses DiamondTough belts. Belts are constructed using a patented triple-weave process of nylon and polyester materials.

    They have the strength to handle heavy shock loads and help maintain consistent belt length.

    The DiamondTough belts are more puncture and tear resistant than other belts on the market and provide improved belt life and reliability.

    Plate-type fasteners
    Plate-type splices Plate-type splices
    #

    All of the 0 Series Balers use the plate-type fasteners.

    This closed-loop design uses a plate fastener with pre-assembled rivets that lock the fasteners into the belt, providing a powerful vice-type grip on the belt.

    • The plates and rivets are manufactured from high-tensile stainless steel.
    • Strong belt splices mean less maintenance and more productivity.
    • The loop area is cold forged, making it extremely wear resistant in the coupling area, resulting in a very long cycle life.
    • The spring steel pin is notched and locks into the splice connection without having to bend the pin or use external retainers.
  • Belts-other - width
    17.8 cm
    7 in.

    Density control
    Hydraulic

    Bale size indication
    Not available from factory, available as dealer-installed options

    Regular pickup - Bars
    Four

    Regular pickup - Number of teeth
    72

    Regular pickup - Tooth spacing
    6 cm
    2.6 in.

    MegaWide Plus pickup - Number of regular teeth

    MegaWide Plus pickup - Number of mega teeth

    High-capacity pickup - Number of middle teeth

    High-capacity pickup - Number of mega teeth

  • Size
    Diameter
    89 - 152 cm
    35 - 60 in.
    Width
    117 cm
    46 in.
    1.2 x 1.5 m
    4 x 5 ft

    Weight
    Full-size bale in dry crop
    454 kg
    1,000 lb

  • Base weight

    Weight

    Shipping - 1,701 kg
    3,750 lb

    Length
    Gate closed
    361 cm
    142 in.
    Gate open
    455 cm
    179 in.

    Height
    Gate closed
    260 cm
    102 in.
    Gate open
    325 cm
    128 in.

    Width
    With standard tires
    226 cm
    89 in.

  • Forming chamber

    Belts-other
    Number
    Six
    Width
    17.8 cm
    7 in.

    Texture
    Diamond Tread friction surface belts
    DiamondTough, triple-weave, single-ply belts

    Enclosed percent of bale surface

    Belt splices

    Density control
    Hydraulic

    Bale size indication
    Not available from factory, available as dealer-installed options

    Bale Shape

  • Type

    Width
    Inside
    117 cm
    46 in.
    Flare
    141 cm
    56 in.

    Drive

    Bars
    Four

    Number of teeth
    72

    Tooth spacing
    6 cm
    2.6 in.

    Lift control
    Adjustable height control

    Gauge wheels
    Semi-pneumatic

    Stripper diameter
    25.4 cm
    10 in.

  • Type

    Width

    Drive

    Bars

    Number of regular teeth

    Number of mega teeth

    Tooth spacing

    Lift control

    Gauge wheels

    Stripper diameter

  • Type

    Width

    Drive

    Bars

    Number of middle teeth

    Number of mega teeth

    Tooth spacing

    Lift control

    Gauge wheels

    Stripper diameter

  • Control
    Automatic to preset to bale size

    Type
    Standard
    Electric

    Twine arms
    Two

    Twine ball capacity
    Four

  • Monitor console for tractor

    Gate closed
    Symbol on monitor

    Bale forming

    Bale size
    Mechanical

    Near full bale
    Audible alert

    Full bale
    Audible alert

    Twine arm position Indicator
    Mechanical

    Auto wrap
    Activates when bale reaches preset size

    Oversize bale
    Yes, audible and mechanical alerts

  • s
    s


    A
    A

  • Standard
    11 L - 14

    Optional

  • Drive protection
    Shearbolt

    PTO speed
    540 rpm

    Type
    Constant-velocity (CV)

    PTO lockback collar on tractor hookup
    No

    PTO 60-degree free rotation
    No

  • Minimum PTO
    Dry Hay and Silage - 42 kW
    55 hp

    Hydraulic SCV valves
    One tractor selective control valve (SCV) is required when baler is equipped with electric twine wrap.
    Two tractor SCVs are required when baler is equipped with hydraulic twine wrap.
    Three tractor SCVs are required when baler is equipped with hydraulic twine wrap and a hydraulic pickup lift.

  • Starter roll scraper

    Powered scraping auger

    Spirals on gate roll

    Pre-cutter/slicer

  • Maintenance chains

    Date collected
    14-February-2018

Related Products