New 1200H Hydro Bunker & Field Rake

Bunker Rakes
REQUEST A QUOTE
REQUEST A QUOTE
Key Features
  • Fuel efficiency at speeds up to 10 mph
  • Standard 72-inch rear rake enables rapid coverage
  • Adjustable seat and wide running boards
  • Stylish rear body

More Info

Features

Wide tires and wheelbase
Wide tiresWide tires

Wide high-flotation tires provide low ground compaction.

  • All tires are 22x11.00x8 NHS

 

The 47-in. (119-cm) wheelbase enables a tight turning radius.

Heavy-duty air filter protects engine in tough conditions

A heavy-duty air filter is standard equipment on the 1200A Bunker and Field Rake.  Featuring a cyclone design, this dual element filter can eject 90 percent to 95 percent of dust particles before they reach the paper element core.  This reduces overall maintenance costs through less cleaning and replacement.

Foot controls
Foot controlsFoot controls

The forward and reverse foot pedals provide ease of identification and operation. The forward pedal is larger than the reverse pedal and provides good clearance for the operator's foot. This is the same two-pedal design used on the  John Deere 2500A Riding Greens Mower.

Engine

Raising the hinged rear fiberglass body cowling exposes the 16-hp*(11.9-kW), 479-cc air-cooled, overhead valve engine:

  • High torque for pulling power
  • Fuel efficient for lower operating cost and extended operating range
  • 3.9 gal (14.8 L) gas tank for long hours of operation with unleaded gasoline
  • Full pressure lubrication and oil filter for good reliability
  • Low vibration for long component life and operator comfort

 

*At 3600 rpm. Engine manufacturer gross power per SAE J1940. Tested in accordance with SAE J1995. The engine hp and torque information are provided by the engine manufacturer for comparison purposes only. Actual operating hp and torque will be less. Refer to the engine manufacturer’s website for additional information.

Drive system
Drive systemDrive system

The hydrostatic 3WD system has variable speed for excellent pulling and pushing power.

Operator's platform designed for operator comfort
Operator's platformOperator's platform

The operator's platform is designed for comfort, control, and high productivity:

  • 14-in. (35.56-cm) diameter steering wheel with a 10-to-1 gear ratio for easy and responsive steering
  • Adjustable for and aft for improved comfort for large and small operators
  • Wide running boards for comfortable leg support of large and small operators alike
Instrumentation is convenient and easy to use
Instrumentation and controlsInstrumentation and controls

Instruments and electronic controls are positioned for easy reach and visibility:

  • Ignition switch and key start are mounted on the console for quick and easy starting.
  • Choke control for quicker cool weather starts is conveniently located on the console at left.
  • Standard rear and mid implement lift lever is located on the right side for easy access.

Specifications

Engine
Manufacturer
Type Air-cooled
Displacement 480 cc
29.3 cu in.
Horsepower At 3600 rpm: 11.9 kW
16 hp
Engine Manufacturer Gross Power per SAE J1940. Tested in accordance with SAE J1995. The engine hp and torque information are provided by the engine manufacturer for comparison purposes only. Actual operating hp and torque will be less. Refer to engine manufacturer's website for additional information.
Compression ratio 8.5:1
Lubrication Full pressure
Oil capacity Without filter: 1.4 L
1.5 U.S. qt
Oil filter Standard
Spark arrester muffler Standard
Idle speed Low speed: 1,750 rpm
fast idle speed (low load): 3,100 rpm
Electrical System
Type 16 amp
12 V
Battery 500 CCA
12 V
Starter Electric
Ignition Transistor type
Light kit Available
Fuel System
Tank capacity 14.8 L
3.9 U.S. gal.
Fuel pump Diaphragm-type
Fuel required Unleaded gasoline
Transmission
Type Hydrostatic with 3 hydraulic wheel motors
Fluid capacity 12.2 L
12.9 U.S. qt
Travel Speed
Forward or reverse Variable: forward: 0-16.09 km/h
0-10 mph
reverse: 0-6.4 km/h
0-4 mph
Brakes
Type Dual rear wheel parking brakes; dynamic braking provided by closed loop hydrostatic powertrain
Steering
Type Chain drive steering wheel with 10-to-1 gear ratio: 35.6 cm
14 in.
Tires
Front One 22x11x8 NHS 34.5 kPa
5 psi
Rear Two 22x11x8 NHS 34.5 kPa
5 psi
Dimensions
Width 1422.4 mm
56 in.
Height 1117.6 mm
44 in.
Length 1676 mm
66 in.
Wheelbase 1193.8 mm
47 in.
Ground clearance @ rake attachment 241 mm
9.5 in.
Turning radius Zero
Weight (approx.) 449 kg
990 lb
Rear-hitch towing capacity
Attachments
Rake
Cultivator
Front blade
60-in. aluminum front blade
Articulating front-mount core-removal blade
Wide- and narrow-interval scarifier tines attachment
Mid-mount 64.5-in. (164.9 mm) scraper blade attachment
Rear-mounted 60-in. field finisher
Hydraulic pump package
Sound Levels
Operator ear 76 dBA
Measuring standard ISO 11201
Attachments installed

Accessories and Attachments

Miscellaneous

Hydro Rake 72 In. Rear Mounted Prong Blade Rake - TCB10891
Rear rakeRear rake

A rear rake is standard equipment.

  • 72-in. wide for rapid coverage
  • Forward, aft, lateral, and side-to-side floating action enables rake to follow ground contours for well-groomed finish
  • Rake assembly quickly detaches in less than one minute, exposing the rear hitch for convenience and added versatility
Hydro Rake Scarifier - TCB10890
ScarifierScarifier

A mid-mount scarifier tine section can be mounted to the 1200 Hydro.

 

The scarifier is recommended where surface cultivation and preparation requirements dictate that small rocks (up to 2-1/2-in. diameter) must be allowed to pass through the scarifier or for relieving surface compaction on skinned areas of baseball fields, running tracks, and athletic complexes. Also works very well for grooming cinder, crushed brick, and small gravel warning tracks.

Light Kit - BTC10094
Mid Mount Cultivator Shoes/Blades - TCB10939
Mid-mount cultivatorMid-mount cultivator

The mid-mounted cultivator is available as an attachment for field conversion that provides more aggressive cultivation and weed control.